DICOVIA => Demandez la traduction d'un mot dans n'importe quelle langue.

Forum de traduction et de présentation de Dicovia.com

Vous n'êtes pas identifié.

#1 06-11-2017 02:24:19

misshuana
Membre
Date d'inscription: 13-07-2016
Messages: 710

if there is any extra functionality

1. The little pineapple snaggletooth
In the daily use of Ball Mill David Robinson Olympics Jersey , the little pineapple snaggletooth happens most often, the reasons are as follows:
(1). The little pineapple design strength is weak, and the manufacturing quality requirements is relatively low.
(2). The lubricating of the little pineapple is bad, the mesh is bad which lead to localized wear, bubbling, and material quality coming off. The local stress concentration is worsened which speed up the snaggletooth.
(3). Supercharge caused by the too many steel balls added into the Coal Ball Mill in production primary which lead to the coal ball mill electric current reaches to 130A. Decrease the steel ball loading capacity Clyde Drexler Olympics Jersey , keeping the current at around 120A. (the current raises 1A with one ton steel ball added,)
2. The little pineapple tooth surface abrasion
The gear wheel surface generally presents bubbling, peeling, scallops, and such corrosive pitting phenomenon. Besides the little pineapple tooth surface temperature is high which makes the coal grinding ball mill gear teeth attrition condition seriously.
The reasons are as follows:
(1). The coal grinding ball mill protection cover sealing is not good. There is no sealing on the association point of activity and inertia between the Coal Mill hollow shaft and shelter which speed up the ash entering to the big pineapple. The preheater of the boiler is the three branch warehouse, with one way the secondary air of the blower Christian Laettner Olympics Jersey , one way the primary air of the primary air fan. As the primary air pressure is over-high, it blows down the ash accumulated from the smoke side carrying by the preheater heating surface and takes it away. The pipeline weld bond of the hot air system is unqualified which leads to serious leakage. The ash then enters to the wheel gear shield and speed up its attrition.
(2) The alignment pin problem: It is regulated that the temperature difference measured along the little cutter teeth width should be no more than 8??, and the highest temperature on the tooth surface should be no more than 100??. Hit the alignment pin in after the intervals between each part is normal. When the temperature difference is more than 8??, raise the bearing end of low temperature. One of the reasons for the ball mill tooth surface attrition is that the alignment pin is not hit due to the great work amount which is also the reason why some individual little cutter teeth surface is high and the two ends temperature difference is relatively large.
It consists of motor, reducer, case Chris Paul Olympics Jersey , milling device, separator, outlet, coal feeding pipe, loading device, control box and sealing apparatus. The fittings are all of superior performance in the world at present. We ensure good quality and durability of the whole machine.

1) The concrete base weight required is only 3 times of that of other similar machines thus the construction expenses is greatly reduced
2) Small vibration while using and doesn't need shock-absorbing device
3) Large load adjustment scope Chris Mullin Olympics Jersey , so it can run under various environments
4) Can bear very strong explosion pressure
5) The grinding roller adopts new material and new craft, which ensures long service life and low maintenance cost
6) There is gap between the grinding parts; it can start with load or offload. Get Mineral Processing,rotary kiln,ball mill From http:www.ballmill8

How To Gain Employment And Avoid Getting Buying Into A Scam: Let’s Review How To Gain Employment And Avoid Getting Buying Into A Scam: Let’s Review October 21, 2013 | Author: Nancy Kennedy | Posted in Careers
Reviewing the internet and trying to find a job, but what do you need to look for? Maybe word of mouth from a friend Charles Barkley Olympics Jersey , some scam blog site that cuts down a company or should you go to the source? When looking for work you cannot help encountering a blog that points out corporations as a devious puppet master stringing its employees along. Trust me you will bump into this a lot.


I find the tone of most of these scam blogs to be written by clearly lazy, unenthusiastic and atrocious spellers that feel better to flame and burn a company that gave that writer the chance to have a career and simply asked that person to do some hard work. So for those of you that are attempting to find a real job that will flourish into a career you can be proud of, review a few helpful tips to get you started on your path.


Check the job sites. Monster, careerbuilder, Indeed and Beyond are just a few of the many reputable sites that can not only find work in your area but give you a review of what is expected of yet environment. These sites are there and ready to assist you in finding that oh so needed work. For example: DMA Portland has openings currently for entry level as well as management positions. How did I find that out? I simply looked it up.


Visiting BBB.org is a smart plan. Upon review, The Better Business Bureau’s reason for being is making certain businesses are held accountable for their actions. Keeping track of genuine complaints and grievances against the company and the compliments of companies’ accomplishments Carmelo Anthony Olympics Jersey , how they hire and overall excellence they adhere to.


Look at the company’s website and review the information presented. With any company large or small they commonly have a company website explaining to you their mission statement, who they are, what they what they want of potential hire ons, their location and finally their contact information. This is convenient when looking for work and gives you some perspective of the business up close.


Talk to a person that works at the company. You’ve done all your homework and get the concept of what this company does but you still have questions. Talk the HR of the company and ask your inquiries. Review if this c. Wholesale NHL Jerseys   Cheap Jerseys   Cheap Jerseys China   Cheap NFL Jerseys   Cheap NFL Jerseys   Wholesale Jerseys Free Shipping   Wholesale NFL Jerseys China   Wholesale Soccer Jerseys From China   Cheap NFL Jerseys   Cheap NFL Jerseys

Hors ligne

 

Pied de page des forums

Créez Votre Propre Forum
Insérer vos Graphiques
Dictionnaires de Traduction
Hébergé par ForumCrea.com